• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Dodge, Jeep and RAM Forum dedicated to FCA owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the SRT Forum today!


Adding a 10% overdrive pulley to an already pinned crank.

fumanchu182

3000 Posts Club
Vendor
Premium Account
U.S. Navy Veteran
Donating Member
9 Second Best E/T
HFCOTM
Member ID
#2366
Messages
3,490
Reactions
8,488
Likes
302
City
Pasadena
State
MD
Country
United States
Vehicle
2015 Challenger SRT Hellcat
#1
When I was stock I pinned my crank using this kit: https://highhorseperformance.com/hh...or-15-current-gen-iii-hemi-supercharged-6-2l/, to prevent my crank head from looking like swiss cheese can I re-use the key hole? Has anyone encountered this before? I'm thinking I can use the kit and overlay it over the key hole and drill that and then re-insert the pin. Good idea/bad idea?
 


16GoManGoHC2

3000 Posts Club
Founding Member
9 Second Best E/T
Member ID
#1139
Messages
3,291
Reactions
7,771
Likes
252
City
Nanticoke
State
PA
Country
United States
Vehicle
2016 Challenger He’ll Cat
#2
I just did this this weekend. Best thing is to machine the new ATI hub to accept a round key where it’s cut for a square key. I’m putting a stock size shell on for now, have a 10% OD and clearanced the AC mounting boss to clear the hub so it’s ready for quick swap between a stock size shell and the 10% OD one. 29B3C420-321F-4BD4-8689-9D3DA7F40178.jpeg 55864019-51E2-4059-A007-7BDE5EFF6AFF.jpeg 721DA250-0A95-4FAF-AC4E-6DB94890A74F.jpeg B4A59D61-C29F-4E14-9574-CB3BD05E75FD.jpeg 72CC556A-949F-47DB-9FF2-5C822203004C.jpeg DBB8609A-5138-4FA8-9C89-9756DEA849D3.jpeg
 


OP
fumanchu182

fumanchu182

3000 Posts Club
Vendor
Premium Account
U.S. Navy Veteran
Donating Member
9 Second Best E/T
HFCOTM
Member ID
#2366
Messages
3,490
Reactions
8,488
Likes
302
City
Pasadena
State
MD
Country
United States
Vehicle
2015 Challenger SRT Hellcat
Thread Starter #3
I don’t have access to a drill press, would I be able to clamp the pin kit to the pulley when not installed and use that as a guide? @16GoManGoHC2
 


16GoManGoHC2

3000 Posts Club
Founding Member
9 Second Best E/T
Member ID
#1139
Messages
3,291
Reactions
7,771
Likes
252
City
Nanticoke
State
PA
Country
United States
Vehicle
2016 Challenger He’ll Cat
#4
I don’t have access to a drill press, would I be able to clamp the pin kit to the pulley when not installed and use that as a guide? @16GoManGoHC2
I doubt it. I do this in a milling machine with a 1/4” end mill. I can do a hub for for if you want to send me one. I would need to know the projection distance of the pin on your crank snout to get it right. The jig does not drill the pin hole exactly 50% in the shaft and 50% in the hub. Easiest and quickest thing for you to do is just mount it and redrill the crank for another pin but yes your crank starts to look ugly after doing this too many times but who’s going to see it under the bolt??? I have the Towing in the ability so that’s just the way I do it I did that to my stock balancer as well notice how the pin groove goes all the way from one side to another that’s how I was able to re-mount it in the same location as it came off when I rebuilt the engine. I cut the groove all the way through the hub so it could follow the existing pin onto the snout when being pressed back on.
55AE2EE0-03E8-4BE3-95FA-6BCB218D36E9.jpeg D837C9C5-4463-4A38-9D9A-735DFF1B3F2D.jpeg
 


white1

Active Member
9 Second Best E/T
Member ID
#5684
Messages
267
Reactions
411
Likes
67
City
Prairieville
State
LA
Country
United States
Vehicle
2020 hellcat charger widebody
#5
I've been able to align the hole close enough to get lucky a couple of times.
its not too hard
 


Speedy!

Infomercial Producer
Staff Team
Founding Member
U.S. Marine Veteran
9 Second Best E/T
HFCOTM & HFCOTY
Member ID
#1070
Messages
6,070
Reactions
15,536
Likes
402
City
Murfreesboro
State
TN
Country
United States
Vehicle
2016 Hellcat Go Man Go
#6
Most do a new pin 180° from original. That's how I'd do it.
 


Blown7

Active Member
Founding Member
Member ID
#1188
Messages
179
Reactions
224
Likes
37
City
Woodstock
State
CT
Country
United States
Vehicle
2018 Trackhawk
#7
Most do a new pin 180° from original. That's how I'd do it.
I the big blower engines I build I install two (2) keyways 180 degrees apart.
Be really cool and install three (3) 120 degrees apart. It transmits something like triple the torque rotation.
 


Unholy707

5000 Posts Club
9 Second Best E/T
HFCOTM
Member ID
#11903
Messages
5,080
Reactions
4,207
Likes
402
City
Orlando
State
FL
Country
United States
Vehicle
2015 Dodge Challenger Hellcat
#8
It’s only half a square hole, should be able the wallop a round peg in there
 




Top